|
Well Pumps Stainless Steel Pumps
|
|
 |
3" WPS-CP Stainless Steel Submersible Pumps
The New Generation of 3" Pumps
Characteristics:
- Entirely made out of stainless steel
- Excellent resistance to wear
- High speed, maximum 8.200 RPM
- Discharge NPT 1 1/4"
- Very easy to install
- Motor developed to run at high speed (140Hz)
- Constant Pressure due to variable speed
- Protection against dry running
- Soft start and stop
- Single phase supply to the controller
- Protection against over and under voltage
- Two set pressures possible
The Kit consists of:
- A 3" submersible pump WPS entirely made of stainless steel. Well Pumps S.A. specially developed this pump for high rotation speeds up to 8.200 RPM.
- A WPS high speed submersible motor able to run at variable frequencies up to 140Hz.
- A WPS-CP constant pressure controller including a variable speed drive, a flow detection and pressure sensor.
- A pressure vessel
The Advantages !
- For 3" wells and bigger
- Pump entirely of stainless steel
- Constant pressure - variable flow
- Fast installation
- Easy to maintain
- Two set pressures possible
Literature
|
|
|
Berkeley Pumps
As Berkeley Dealers we sell, maintain and service on site. All warranties are handled at our location.
|
|
 |
H Series
Precision-engineered, high-quality, rugged Signature 2000® stainless steel Series H pumps in 5 through 50 GPM models deliver efficient, dependable performance even in rough, aggressive water.
- Patented Staging System - Greatly reduces problems with abrasives, sand lockup and running dry.
- Stainless Steel Configuration.
- Stainless Steel Coupling - Couples to all standard NEMA motors.
- Wide Range of Sizes - Available for most applications
Literature
|
|
 |
J Series
Series J are precision-engineered, corrosion-resistant Signature 2000® pumps in 5,7,10,15, 20 and 30 GPM models deliver efficient, dependable performance even in rough, aggressive water.
- Patented Staging System - Greatly reduces problems with abrasives, sand lockup and running dry.
- Discharge - Corrosion-resistant fiberglass reinforced thermoplastic for durability in aggressive water. Large octagon wrench area for ease of installation.
- Stainless Steel Coupling - Couples to all standard NEMA motors.
- Wide Range of Sizes - Available for most applications
Literature
|
|
 |
70 Series
Precision engineered, quality built, and rugged 70 GPM Series submersibles may be used in wells 4" or larger. Maximum outside diameter 3-7/8".
- Discharge – Heavy-duty cast iron construction provides smooth water passage to column pipe. NPT threads standard.
- Bowl and Intake Bearings – Fluted, cutless rubber type assures superior abrasive-handling characteristics, located at each stage.
- Polycarbonate Impellers – Glass-reinforced polycarbonate resists abrasives and provides smooth water passages for minimum friction loss. Ensures optimum pump efficiency.
- Ideal for residential, industrial, commercial, multiple housing and farm use.
Literature
|
|
 |
90 Series
The 90 GPM Stainless Steel High-Flow 4" Submersible Pumps deliver efficient and dependable performance even in rough, aggressive water.
- Discharge – Heavy-duty 300 grade stainless steel construction provides smooth water passage to column pipe.
- Top Bearing – Field-proven, sealed and lubricated top bearing assembly keeps abrasives out, ensuring long bearing life.
- Impellers – 20% glass-reinforced polycarbonate to resist abrasive sand provide smooth water passage for minimal friction loss.
- Ideal for residential, industrial, commercial, multiple housing and farm use.
Literature
|
|
 |
Submersible Motor Controls
Ideal for water systems applications in residential, commercial, multiple housing and farm settings, where a submersible 3-wire motor is used.
- Enclosure - Rugged NEMA 3R Enclosure - suitable for indoor/outdoor use. NEW HardBond™ Finish - 5-times more corrosion-resistant. Multiple-size electrical knockouts.
- Internals - Full Range 1/2-15HP Models available - Capacitor Start/Induction Run (CSIR). Capacitor Start/Capacitor Run (CSCR), with and without magnetic contactors. Interchangeable with existing motor controls. High-load Voltage Relay, Potential Design - Decades of proven field-service; Heavy duty contacts; Professional's choice in high ambient temperature installations; External access to overload reset - CSCR. Heavy-Duty Terminal Connectors: Suitable for up to #4 AWG wire; Industry standard wiring connections-easy-to-read wiring diagrams.
- Agency Approvals - UL 778 and CUL Listed
- Available in: Capacitor Start/Induction Run; Capacitor Start/Capacitor Run; Capacitor Start/Capacitor Run with Magnetic Contactors.
- Rugged NEMA 3R Enclosure - Suitable for indoor/outdoor use
- NEW HardBond™ Finish - 5-times more corrosion-resistant
- High-load Voltage Relay
- Heavy-duty Contacts
Literature
|
|
 |
HS+ Series
The Signature 2000® HS+ series puts the plus in HS+ with the advanced PENTEK® XE Series™ motor. Superior PENTEK® motor technology supercharges an HS+ pump with extra stages.
- Patented Staging System - Our proven SignaSeal staging system incorporates a harder-than-sand ceramic wear surface that when incorporated with our floating impeller design, greatly reduces problems with abrasives, sand lock-up and running dry
- Discharge - Corrosion-resistant 300 grade stainless steel for durability in aggressive water. Large octagon wrench area for ease of installation
- Discharge Bearing - Exclusive self-lubricating Nylatron bearing resists wear from sand
- Intake - Corrosion-resistant 300 grade stainless steel for durability in aggressive water
Literature
|
|
 |
L6TS Series
The L6TS Series Submersible features heavy-duty 304 stainless steel construction that will outperform ordinary fabricated stainless steel pumps in aggressive water conditions.
- Heavy-Duty, Investment Cast 304 Stainless Steel Discharge and Suction Bracket - Assures perfect pump-to-motor alignment with any NEMA-standard submersible motor. Discharge assures secure connection to drop pipe. Wrench flats provide positive grip during installation
- Low-Profile Stainless Steel Lead Guard - Aids installation in narrow wells
- Wide Range of Performance Options - 1 HP to 60 HP; 29 to 365 U.S. GPM
- Hard Chrome-plated Top Bearing Journal - Reduces wear in harsh conditions, such as sand
Literature
|
|
 |
6T Series
6T Series submersible pumps are designed for continuous duty applications in 7" or larger wells.
- Eleven models with flows to 450 GPM, Pressures to 1400 feet (600 psig).
- 304 stainless steel investment cast impellers.
- 416 stainless steel pump shaft, ground & polished for maximum durability. Optional hard chrome shafting for severe abrasives.
- Heavy-duty cast iron suction bracket - assures perfect pump-to-motor alignment with any NEMA standard submersible motor.
Literature
|
|
 |
6TS Series
6TS Series submersible pumps are designed for continuous duty applications in 7" or larger wells.
- Five models, with flows to 300 GPM, Pressures to 1400 feet (600 psig).
- 304 stainless steel hydraulic components, 304 stainless steel cast iron suction & discharge brackets and hard chrome bearing journals provide the ultimate in corrosion resistance & durability.
- Self-aligned Teflon® wear rings improve pump efficiency and durability
- Built-in check valve prevents backflow and reverse rotation.
Literature
|
|
 |
7T Series
7T Series submersible pumps are designed for continuous duty applications in 8" or larger wells.
- Five models with flows to 500 GPM, Pressures to 1400 feet (600 psig).
- 304 stainless steel investment cast impellers.
- 416 stainless steel pump shaft, ground & polished for maximum durability. Optional hard chrome shafting for severe abrasives.
- Heavy-duty cast iron suction bracket - assures perfect pump-to-motor alignment with any NEMA standard submersible motor.
Literature
|
|
 |
8T Series
8T Series submersible pumps are suited for dependable and continuous duty applications in the industrial, municipal, commercial and agricultural applications, in 10" or larger wells.
- Five models, with flow to 1000 GPM, pressures to 1100 feet (475 psig).
- Silicon Brass Impellers - are designed and machined to optimize efficiency and performance.
- Unique Neoprene bearing design - channels abrasives away from stainless steel bearing journal. Non-corrosive sand cap - protects bronze suction bracket bearing and stainless steel bearing journal.
- Low profile, full-length stainless steel cable guard - protects motor leads.
Literature
|
|
 |
10T Series
10T Series submersible pumps are suited for applications in the industrial, municipal, commercial and agricultural applications, in 12" or larger wells.
- Four Models, with flows to 2200 GPM. Pressures to 450 feet (200 psig).
- Silicon Brass Impellers - are designed and machined to optimize efficiency and performance.
- Unique Neoprene bearing design - channels abrasives away from stainless steel bearing journal. Non-corrosive sand cap - protects bronze suction bracket bearing and stainless steel bearing journal.
- Low profile, full-length stainless steel cable guard - protects motor leads.
Literature
|
|
 |
6" Hitachi Submersible Motor
6" Hitachi submersible motors are fully featured for many years of dependable operation.
- Higher Efficiencies
- Epoxy Filled - Provides excellent heat conductivity
- Lower Current Consumption - For reduced energy costs
- Kingsbury-Type High-Capacity Thrust Bearings
Literature
|
|
 |
70 GPM Series
Precision-engineered, quality built, and rugged 70 GPM Series submersibles may be used in wells 4" or larger.
- Discharge - Heavy-duty cast iron construction provides smooth water passage to column pipe. NPT threads standard.
- Bowl and Intake Bearings - Fluted, cutless rubber type assures superior abrasive-handling characteristics, located at each stage.
- Polycarbonate Impellers - Glass-reinforced polycarbonate resists abrasives and provides smooth water passages for minimum friction loss. Ensures optimum pump efficiency.
Literature
|
|
 |
Mining DeepSet
Precision-engineered, high-quality, rugged MGS Stainless Steel Series Pumps deliver efficient, dependable performance even in rough, aggressive water.
- Patented Staging System - Our higher temperature engineered thermoplastic patented SignaSeal staging system incorporates a harder-than-sand ceramic wear surface that when incorporated with our floating impeller design, greatly reduces problems with abrasives, sand lock-up and running dry.
- Discharge - Corrosion-resistant 300 grade stainless steel for durability in aggressive water.
- Discharge Bearing - Exclusive self-lubricating Nylatron bearing resists wear from sand.
Literature
|
|
 |
4" x 6" Adapter
The PKG 4x6, Pump/Motor Adapter offers the professional distributor and dealer the flexibility to stock standard 4" submersible pump ends, and 4" and 6" Motors, better utilizing inventory dollars and delivery demands!
- Extends Single-phase Power Availability - To all Signature 2000® submersibles through 10 HP using 6" single-phase motors
- Easy Assembly - Easy job-site assembly
- Double-suction Screens - Reduces inlet suction velocity, reducing the amount of suspended solids ingested by pump
- Extends Single-phase Power Availability - To all Signature 2000® submersibles through 10 HP using 6" single-phase motors
- Easy Assembly - Easy job-site assembly
- Double-suction Screens - Reduces inlet suction velocity, reducing the amount of suspended solids ingested by pump
Literature
|
|
 |
4" Submersible Motors
Feature laser-welded 304L stainless steel construction, higher thrust capacities and higher efficiencies.
- Kingsbury Thrust Bearing Design - Large high-performance bearings are standard on all HPs allowing for higher thrust loads, providing many years of trouble-free service under severe-duty operation.
- 2-Wire Permanent Split Capacitor - Design insures quiet operation and improved operating efficiency.
- 3-Wire Motors - Operate with PENTEK® SMC and other single-phase motor controls.
Literature
|
|
 |
Single Phase Pump Protectors
Full range of 1/3 - 15 HP single-phase protectors were a 4" submersible, 2- and 3-wire motor is used and for aboveground pressure-boost applications.
- PENTEK® offers 5 models for your application needs based on HP and Motor Type: SPP-111, SPP-111-3RL, SPP-231, SPP-233 and SPP-235.
- Protects Pumps - from dry well, overcurrent (jammed impeller), flow restriction (dead head), overvoltage, undervoltage, rapid cycling.
Literature
|
|
 |
Constant Pressure Controller
Can be used in both belowground submersible and aboveground centrifugal pressure system applications, using a 3-phase motor.
- Easy to Install - Similar to a control-box installation.
- Built-in Start-up Diagnostic - Calibration to site and well conditions.
- Soft Starts/Stops - Reduce water hammer and increase pump efficiency.
Literature
|
   |
